How to Remove and also Replace a Bathtub.
How to Remove and also Replace a Bathtub.
Blog Article
We have noticed the article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the internet and decided it made perfect sense to discuss it with you over here.
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. Ensure you have certified yourself for the job as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will aid you install a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub as well as do not need to transform the setup of your previous supply of water pipelines.
Your tools as well as material checklist need to comprise the following:
Getting ready for the Installment
Firstly, the supporting structure provided with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The process of removing the existing taps can be quite problematic due to the restricted accessibility that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will come from the pipelines. As soon as the supply pipelines have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the needed position. The wooden boards are useful in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by checking the level as well as changing the feet on the bathtub till the level reads degree.
To mount taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has been made use of at least when as this will settle it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place between the tap and the sink. Protect the faucet in position with the supplier provided backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads on Installing A Bathtub, I assumed sharing that excerpt was a smart idea. Feel free to set aside a second to share this blog post if you enjoyed reading it. Many thanks for your time. Please visit our site back soon.
Visit Link Report this page